TL084ACNSR
| Parameters | |
|---|---|
| Max I/O Voltage | 6mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL084 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Circuits | 4 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 11.2mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
TL084ACNSR Overview
Op amp is packaged in 14-SOIC (0.209, 5.30mm Width) case. The instrumentation amplifier in this picture is of the J-FET-type. A Cut Tape (CT) case is used for delivering the op amp. It is estimated that there will be 14 terminations in the next few months. Buffer amplifier has a total of 14 pins. Please take in mind that op amp should be run at 15V. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 14 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . As long as the supply current of the chip does not exceed 1.4mA, this op amp ic can operate. There should be no change in the voltage gain at 106.02dB. There are 4 circuits on op amps. The operating supply voltage of the buffer op amp is rated at 18V. TR is adopted to pack the instrumentation amplifier.
TL084ACNSR Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL084ACNSR Applications
There are a lot of Texas Instruments TL084ACNSR Instrumentational OP Amps applications.
- Proportional operation circuits
- Proportional counter tubes
- pH (acidity)
- PDA
- Switching amplifier
- Commercial audio systems
- Fission chambers
- Strain gauges
- earphone
- Subtraction operation circuits
