TL084BCDT
| Parameters | |
|---|---|
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 680mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL084 |
| Pin Count | 14 |
| Number of Elements | 4 |
| Power Supplies | +-15V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Power Dissipation | 680mW |
| Output Current | 40mA |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
TL084BCDT Overview
In the package, you will find a 14-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp ic of the J-FET type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 14. Linear amplifier has a total of 14 pins. This linear amplifier should be powered by an 15V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The op amp ic has an array of 14 pins on it. With regard to input offset voltage, instrumentation amplifier is rated at 3mV. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of 0°C~70°C. A supply current of 1.4mA can be used to operate this linear amplifier. 106.02dB should remain the voltage gain. As a whole, there are 4 elements that make up this buffer amplifier. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
TL084BCDT Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL084BCDT Applications
There are a lot of STMicroelectronics TL084BCDT Instrumentational OP Amps applications.
- Division circuits
- Signal filtering
- Video conversion and routing
- Proportional counter tubes
- Industrial control system
- High speed sample
- Non-polarized electrodes
- Scintillation detectors
- Power transmission
- Subtraction operation circuits
