TL084IDRE4
| Parameters | |
|---|---|
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL084 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Number of Elements | 4 |
| Power Supplies | +-15V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 11.2mA |
| Power Dissipation | 680mW |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
TL084IDRE4 Overview
There is a 14-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. Op amps are J-FET types of amplifier on the chip. A Tape & Reel (TR) case is used to deliver the buffer op amp. There have been a total of 14 terminations over the past year. In total, there are 14 pins on this op amp ic. This linear amplifier should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 14-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 6mV. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . As long as the supply current of the chip does not exceed 1.4mA, this op amp ic can operate. You should keep the voltage gain at 106.02dB for the time being. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 4. The operating supply voltage of the buffer op amp is rated at 18V. This linear amplifier pack is based on the TR axis.
TL084IDRE4 Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL084IDRE4 Applications
There are a lot of Texas Instruments TL084IDRE4 Instrumentational OP Amps applications.
- Test and measurement instruments
- Measurements of Wheatstone bridge
- Differentiator circuits
- Car stereo
- Gaming industry
- Video amplifiers
- Non-polarized electrodes
- High/low-pass filter circuit
- Ultrasound transducers
- Video data acquisition
