TL084IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 4.535924g |
| Operating Temperature | -40°C~105°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 680mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL084 |
| Pin Count | 14 |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Power Dissipation | 680mW |
| Output Current | 40mA |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Dual Supply Voltage | 9V |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height | 1.65mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL084IDT Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. An op amp ic of the J-FET type. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. There have been a total of 14 terminations over the past year. There are a total of 14 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 15V battery. It should be noted that this op amp is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 10mV. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~105°C. The buffer amplifier is capable of operating from a supply current of 1.4mA . Voltage gain should remain at 106.02dB. The op amp ic has 4 channels on it. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
TL084IDT Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL084IDT Applications
There are a lot of STMicroelectronics TL084IDT Instrumentational OP Amps applications.
- Biopotential
- Power control
- Computer workstations
- Logarithmic operation circuits
- High input resistance broadband
- Commercial audio systems
- single/dual op amp sum and difference circuits
- Exponential operation circuits
- Multiplication circuits
- Ultrasound transducers
