TL2842BP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 440.409842mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Frequency | 500kHz |
| Base Part Number | TL2842 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 30V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 10V~30V |
| Control Features | Frequency Control |
| Topology | Boost, Flyback, Forward |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | Up to 500kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 50ns |
| Supply Current-Max (Isup) | 30mA |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 50 ns |
| Nominal Input Voltage | 5.5V |
| Max Duty Cycle | 100 % |
| Duty Cycle (Max) | 96% |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL2842BP Overview
It comes in a 8-DIP (0.300, 7.62mm) package, so switching controller can be used for most applications. 1 outputs can be generated with the dc motor controller. An enclosure of Tube is used to package the PMIC. The system can process Transistor Driver dc switching's outputs (s). DC control operates at 10V~30V volts and has 10V~30V supply voltage. Worked in a -40°C~85°C TA dc switcher before. There is a switch at Up to 500kHz that can be used with this controller. dc dc regulator can be generalized using Through Hole. Frequency Control is used for efficient switching control in the dcdc regulator. An analog IC SWITCHING CONTROLLER is connected to the switch converters. Thare switching converters has a terminal (s) at DUAL . The 8 terminations can be used for a wide range of dc switching. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. DC switcher's input voltageis 15V volts. TL2842 can be searched for other relevant dc to dc converter ics. 8 pins are present on switching converter. Switching converter is a special type of Switching Regulator or Controllers. A 30V voltage of DC regulator was detected in the test statistics. A starting point for a project is to note down the dc dc regulator's usual output current, which is 200mA. A duty cycle set at 100 % ensures voltage regulator dc to dc reliability during power-on and power-off. Switching controller operates at a frequency of 500kHz. It is possible to set the input voltage to 5.5V for nominal working status. This voltage controller requires a supply voltage of 15V. A controller's current should not exceed 30mA.
TL2842BP Features
Transistor Driver Outputs
Switching Frequency: Up to 500kHz
Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 100 %
Frequency: 500kHz
TL2842BP Applications
There are a lot of Texas Instruments TL2842BP DC to DC converter applications.
- Laboratories
- Printing equipment
- Serial communication converter
- Computed tomography (CT)
- Grinders
- Electrical power transmission
- Remotely powered electric motors
- Domestic water pumps
- Injection molding machinery
- Precision electronic equipment
