TL3472CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL3472 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 9mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 100nA |
| Voltage - Supply, Single/Dual (±) | 4V~36V ±2V~18V |
| Output Current per Channel | 34mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 500μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 4MHz |
| Max I/O Voltage | 10mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.075μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL3472CDR Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are available on the instrumentation amplifier. Op amp rates 10mV as input offset voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. An 3.5mA volt supply current is needed for this linear amplifier to operate. It is recommended to keep the voltage gain at 100dB at all times. On the buffer amps, there are 2 channels that can be used. The operating supply voltage of instrumentation amplifier is rated 18V voltage. A TR-shaped amplifier is used to pack the buffer amps.
TL3472CDR Features
8 Pins
supply voltage of 15V
100dB voltage gain
TL3472CDR Applications
There are a lot of Texas Instruments TL3472CDR Instrumentational OP Amps applications.
- Ultrasound transducers
- pH (acidity)
- Large motor controllers
- Television broadcasting equipment
- Navigation
- Cinema or auditorium audio system
- Division circuits
- Signal amplification
- Digital cameras
- Test equipment
