TL3472CDRG4
| Parameters | |
|---|---|
| Package / Case | SOIC |
| Surface Mount | YES |
| Number of Pins | 8 |
| Packaging | Tape and Reel |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 105°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 2 |
| Power Supplies | 5/+-15V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 9mA |
| Slew Rate | 13 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 500nA |
| Output Current per Channel | 34mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.7μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 18V |
| Min Dual Supply Voltage | 2V |
| Bias Current-Max (IIB) @25C | 500μA |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 4MHz |
| Max I/O Voltage | 10mV |
| Height | 1.58mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
TL3472CDRG4 Overview
A SOIC case is used to package the op amp. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tape and Reel case. It is estimated that there will be 8 terminations in the next few months. In total, there are 8 pins on this op amp ic. This linear amplifier should be powered by an 15V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. Linear amplifier includes 8 pins. The input offset voltage is 10mV. Using a supply current of 3.5mA , this buffer op amp will be able to operate. There should be no change in the voltage gain. For this linear amplifier to work, the temperature should not be below -40°C. At temperatures greater than 105°C, Instrumentation amplifier should not be used. There are a total of 2 elements in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 18V. When it comes to the voltage from which this electrical part will operate, it can operate at a maximum of less than 36V. As a general rule, it is advisable to keep the op amp's supply voltage above 4V at all times. In order for this electronic part to be conducted successfully, you should use a dual supply voltage of 18V.
TL3472CDRG4 Features
8 Pins
supply voltage of 15V
100dB voltage gain
TL3472CDRG4 Applications
There are a lot of Texas Instruments TL3472CDRG4 Instrumentational OP Amps applications.
- Digital cameras
- Exponential operation circuits
- Differentiator circuits
- Video conversion and routing
- Automation control systems
- Switching amplifier
- Proportional counter tubes
- Subtraction operation circuits
- Automotive sensors
- Home audio systems
