TL3474ACDR
| Parameters | |
|---|---|
| Number of Circuits | 4 |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 18mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 100nA |
| Voltage - Supply, Single/Dual (±) | 4V~36V ±2V~18V |
| Output Current per Channel | 34mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.5μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 4MHz |
| Max I/O Voltage | 3mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.075μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL3474 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/+-15V |
TL3474ACDR Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. Upon delivery, op amp ic is packaged in a Cut Tape (CT) case. The number of terminations approaches 14. Buffer amplifier has a total of 14 pins. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 14 pins are included on the operational amplifiers. Regarding input offset voltage, op amp rates 1mV. Surface Mount is the recommended mounting type of operational amplifiers. With regard to operating temperature, op amp ranges 0°C~70°C. As long as the supply current of the chip does not exceed 3.5mA, this op amp ic can operate. Keeping the voltage gain at 100dB is the best course of action. There are 4 circuits on this op amp. The operating supply voltage of the buffer op amp is rated at 18V. As a result of this, the buffer amplifier is packed in TR.
TL3474ACDR Features
14 Pins
supply voltage of 15V
100dB voltage gain
TL3474ACDR Applications
There are a lot of Texas Instruments TL3474ACDR Instrumentational OP Amps applications.
- Weak signal detection
- Comparator
- Signal amplification
- High/low-pass filter circuit
- Navigation
- Car stereo
- Medical instruments
- Precision measurement
- PDA
- Portable docking station
