TL3474AIPWE4
| Parameters | |
|---|---|
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 18V |
| Low-Bias | NO |
| Micropower | NO |
| Min Dual Supply Voltage | 2V |
| Bias Current-Max (IIB) @25C | 0.5μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 4MHz |
| Max I/O Voltage | 3mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.075μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Package / Case | TSSOP |
| Surface Mount | YES |
| Number of Pins | 14 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 105°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Packing Method | TUBE |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/+-15V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 18mA |
| Slew Rate | 13 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 500nA |
| Output Current per Channel | 34mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 4MHz |
TL3474AIPWE4 Overview
Op amp is packaged in TSSOP case. Op amps are OPERATIONAL AMPLIFIER types of amplifier on the chip. During the past two weeks, there have been close to 14 terminations. Buffer amplifier has a total of 14 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. It has 14 pins that make up the linear amplifier. The input offset voltage is 1mV. The buffer amplifier is capable of operating from a supply current of 3.5mA . 100dB should remain the voltage gain. 4 channels are available on the instrumentation amplifier. Using this buffer op amp requires a temperature of at least -40°C. At temperatures greater than 105°C, Instrumentation amplifier should not be used. The operating supply voltage of the buffer op amp is rated at 18V. TUBE is adopted to pack the instrumentation amplifier. This electric component can work from a voltage of under 36V as far as supply voltage is concerned. To keep the buffer amps' supply voltage higher than 4V. This electrical part should be conducted under the dual supply voltage of 18V volts when you conduct this part.
TL3474AIPWE4 Features
14 Pins
supply voltage of 15V
100dB voltage gain
TL3474AIPWE4 Applications
There are a lot of Texas Instruments TL3474AIPWE4 Instrumentational OP Amps applications.
- Displayers for aircraft and air transportation control systems
- Strain gauges
- Integrator circuits
- E-book readers
- High input resistance broadband
- Broadcasting
- Band-stop filter
- Television broadcasting equipment
- Semiconductor detectors
- MP3
