TL3474CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL3474 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Number of Elements | 4 |
| Power Supplies | 5/+-15V |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 18mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 100nA |
| Voltage - Supply, Single/Dual (±) | 4V~36V ±2V~18V |
| Output Current per Channel | 34mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.5μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 4MHz |
| Max I/O Voltage | 10mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.075μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL3474CDR Overview
There is a 14-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 14 terminations. In total, there are 14 pins on this op amp ic. I would like to remind you that this buffer op amp should be powered by an 15V battery. It should be noted that this op amp is a type of Operational Amplifier device. It has 14 pins that make up the linear amplifier. Op amp ic rates 10mV for input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . Operational amplifier can operate supply current at 3.5mA. There should be no change in the voltage gain. A total of 4 elements are present in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. For the packing of the instrumentation amplifier, TR is adopted.
TL3474CDR Features
14 Pins
supply voltage of 15V
100dB voltage gain
TL3474CDR Applications
There are a lot of Texas Instruments TL3474CDR Instrumentational OP Amps applications.
- Band-pass filter
- Instrumentation
- High input resistance broadband
- Video amplifiers
- Video computer boards
- Weak signal detection
- Subtraction operation circuits
- Scintillation detectors
- Automotive sensors
- Hand-held batteries
