TL4581DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL4581 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Circuits | 2 |
| Operating Supply Current | 8mA |
| Nominal Supply Current | 16mA |
| Output Current | 38mA |
| Slew Rate | 9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 200nA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~15V |
| Output Current per Channel | 38mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 10MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 1μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 10MHz |
| Max I/O Voltage | 4mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.15μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL4581DR Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. Op amps are General Purpose types of amplifier on the chip. A Cut Tape (CT) case is used for delivering the op amp. The number of terminations approaches 8. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 15V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. The input offset voltage is 500μV. This electrical part should be mounted using type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 8mA and 10 . 100dB should remain the voltage gain. There are 2 circuits on op amps. The operating supply voltage of the buffer op amp is rated at 15V. The instrumentation amplifier is packed in the form of TR.
TL4581DR Features
8 Pins
supply voltage of 15V
100dB voltage gain
TL4581DR Applications
There are a lot of Texas Instruments TL4581DR Instrumentational OP Amps applications.
- Exponential operation circuits
- Signal operation
- Portable electronic products powered by batteries
- Wireless base stations
- Proportional operation circuits
- Home audio systems
- High speed sample
- Navigation
- Fission chambers
- Power generator
