TL494IN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Supply Voltage | 15V |
| Frequency | 300kHz |
| Base Part Number | TL494 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 40V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 15V |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 7V~40V |
| Control Features | Dead Time Control, Frequency Control |
| Input Voltage (Min) | 7V |
| Topology | Buck, Boost, Flyback, Forward Converter, Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 1kHz~300kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 100ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 40 ns |
| Max Duty Cycle | 45 % |
| Output Phases | 1 |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL494IN Overview
This switching controller fits most application requirements since it is packaged in a 16-DIP (0.300, 7.62mm) package. There is sufficient capacity to generate switching controller for outputs 2. The pmic is packaged in Tube solid enclosure. Transistor Driver dc switching's outputs (s) are supported. dc controls with 7V~40V voltage are supplied and operated. Suitable for a -40°C~85°C TA dc switcher. With this switching controller, you can switch at 1kHz~300kHz. As it has a Through Hole value, it can be used for general dc dc regulator. Featured in the dcdc regulator is Dead Time Control, Frequency Control which allows efficient switching control. An analog IC SWITCHING CONTROLLER is connected to the switch converters. A switching converters's terminal (s) sits at the DUAL position. An array of 16 terminations of dc switching. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. 15V nominal DC switcher's voltage input. You can find other relevant dc to dc converter ics by searching "TL494". There are only 16 pins on switching converter. Specially, switching converter corresponds to type Switching Regulator or Controllers. dc dc voltage regulators should have a minimum input voltage of 7V. The test statistics indicate that DC regulator outputs a voltage of 40V. If you start a project, note down the dc dc regulator's usual output current of 200mA. It is set to 45 % duty cycle to ensure voltage regulator dc to dc reliability during power-ups and power-downs. Switching controller operates at 300kHz Hz. A circuit should contain 15V in order to ensure the voltage regulator dc to dc runs safely and reliably. The supply voltage should be 15V.
TL494IN Features
Transistor Driver Outputs
Switching Frequency: 1kHz~300kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 45 %
Frequency: 300kHz
TL494IN Applications
There are a lot of Texas Instruments TL494IN DC to DC converter applications.
- Wide-range voltage regulation circuits
- Telecommunications equipment
- Laboratories
- Computer-related products
- Computer application technology
- Motor controller circuits
- Various precision measuring instruments
- Digital precision reference circuits
- Correction machines
- Radio equipment
