TL5001ACDG4
| Parameters | |
|---|---|
| Package / Case | SOIC |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -20°C |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Max Output Current | 3A |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 6V |
| Temperature Grade | OTHER |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Current - Output | 20mA |
| Quiescent Current | 1.1mA |
| Frequency (Max) | 500kHz |
| Max Output Voltage | 50V |
| Voltage - Output | 50V |
| Topology | Boost, Flyback |
| Min Input Voltage | 3.6V |
| Control Mode | VOLTAGE-MODE |
| Max Input Voltage | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Min Output Voltage | 1V |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 100 % |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
TL5001ACDG4 Overview
This switching controller fits most application requirements since it is packaged in a SOIC package. For outputs of 1, this dc motor controller is suitable. An analog IC SWITCHING CONTROLLER is connected to the switch converters. There are a DUAL terminal on the switching converters. Different dc switching's functions can be applied to 8 terminations. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. DC switcher's voltage input is 6V. Switching converter has a total of 8 pins. Switching converter is a special type of Switching Regulator or Controllers. If the user wishes to run the voltage regulator dc to dc in a circuit safely and reliably, they should apply 40V. Temperatures should be kept at -20°C or higher. At85°C, dc regulator should run. Total number of functions (s) for thare switch converters are 1. In a dormant state, the dc switching uses 1.1mA. We design voltage regulators switchings with 8 pins. There is a maximum frequency of 500kHz that can be switched by the controller. The dc switcher's maximum input voltage is 40V; users must limit it accordingly. Ideally, it is suited for switching controllers with a 20mA input. normalworking processes output 50V voltage. Voltage 3.6V must be supplied. There will be 3A output current greater than 3A from the dc switcher. Its datasheet indicates the switching converter can output a maximum of 50V volts. Neither the voltage controller's lowest voltage output 1Vr its highest voltage output is less than 1V.
TL5001ACDG4 Features
PULSE WIDTH MODULATION
TL5001ACDG4 Applications
There are a lot of Texas Instruments TL5001ACDG4 DC to DC converter applications.
- Overvoltage protection circuits in TV sets
- Computed tomography (CT)
- Smoke exhaust equipment
- Electrical power transmission
- Hydrogen power
- Power supplies of electronic gadgets
- PSRR circuits
- Wind power
- Energy management systems
- Scientific research
