TL5001CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -20°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 500kHz |
| Base Part Number | TL5001 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 50V |
| Output Type | Transistor Driver |
| Max Output Current | 3A |
| Input Voltage-Nom | 6V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 1.1mA |
| Output Configuration | Positive |
| Output Current | 20mA |
| Voltage - Supply (Vcc/Vdd) | 3.6V~40V |
| Quiescent Current | 1.1mA |
| Control Features | Dead Time Control, Frequency Control |
| Max Output Voltage | 50V |
| Topology | Buck, Boost, Flyback |
| Min Input Voltage | 3.6V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 20kHz~500kHz |
| Max Input Voltage | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 1V |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 100% |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL5001CDR Overview
In the 8-SOIC (0.154, 3.90mm Width) package, the switching controller meets most application requirements. There is enough capacity in the dc motor controller to generate the output for the 1 input. Packaging for the pmic consists of Cut Tape (CT) solid enclosures. There are Transistor Driver dc switching's output (s) that it can handle. A 3.6V~40V voltage is supplied to the dc control and used for operating it. Work well in dc switchers with a -20°C~85°C TA. It can switch at 20kHz~500kHz. dc dc regulator can be generalized using Surface Mount. To provide efficient switching control, Dead Time Control, Frequency Control is included in the dcdc regulator. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. There are a DUAL terminal on the switching converters. Different dc switching's functions can be applied to 8 terminations. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. DC switcher's input voltageis set to 6V. Other relevant dc to dc converter ics can be found by searching "TL5001". Total pins of switching converter are 8. DC regulator outputs 50V voltage according to the test statistics. It's important to remember that the dc dc regulator's normaloutput current is 20mA, so you should note it down when starting a new project. A frequency of 500kHz is set for the switching controller. A dc switching in a dormant state uses 1.1mA. Since the dc switcher's maximum input voltage is 40V, the voltage must be regulated accordingly. There must be a 3.6V supply voltage. A dc switcher can only produce an output current of 3A. The datasheet indicates that the switching converter can output 50V volts at its maximum. A supply current of 1.1mA is used to power it. At least 1V voltage is output by the voltage controller.
TL5001CDR Features
Transistor Driver Outputs
Switching Frequency: 20kHz~500kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Frequency: 500kHz
TL5001CDR Applications
There are a lot of Texas Instruments TL5001CDR DC to DC converter applications.
- Milling machines
- Computer monitoring equipment of building
- seismic instrument power circuits
- Emergency lighting monitoring equipment
- Injection molding machinery
- Gear/thread machining machines
- Automatic plug-in machines
- Computer rooms
- Communication system
- Shearing machines
