TL5001CP

8 Terminals 3.6V~40V 8-Pin TL5001 DC to DC converter ICSWITCHING CONTROLLER 1 Outputs 20kHz~500kHz Transistor Driver

Manufacturer: Texas Instruments
Nocochips NO: 815-TL5001CP
Package: 8-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 801
Description: 8 Terminals 3.6V~40V 8-Pin TL5001 DC to DC converter ICSWITCHING CONTROLLER 1 Outputs 20kHz~500kHz Transistor Driver (Kg)

Details

Tags

Parameters
Package / Case	8-DIP (0.300, 7.62mm)
Surface Mount	NO
Number of Pins	8
Weight	440.409842mg
Operating Temperature	-20°C~85°C TA
Packaging	Tube
JESD-609 Code	e4
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Terminal Finish	Nickel/Palladium/Gold (Ni/Pd/Au)
Terminal Position	DUAL
Peak Reflow Temperature (Cel)	260
Terminal Pitch	2.54mm
Frequency	500kHz
Base Part Number	TL5001
Function	Step-Up, Step-Down, Step-Up/Step-Down
Number of Outputs	1
Output Voltage	50V
Output Type	Transistor Driver
Max Output Current	3A
Input Voltage-Nom	6V
Analog IC - Other Type	SWITCHING CONTROLLER
Output Configuration	Positive
Power Dissipation	1W
Output Current	20mA
Voltage - Supply (Vcc/Vdd)	3.6V~40V
Max Supply Current	2.1mA
Quiescent Current	1.1mA
Control Features	Dead Time Control, Frequency Control
Max Output Voltage	50V
Topology	Buck, Boost, Flyback
Min Input Voltage	3.6V
Control Mode	VOLTAGE-MODE
Frequency - Switching	20kHz~500kHz
Max Input Voltage	40V
Control Technique	PULSE WIDTH MODULATION
Synchronous Rectifier	No
Nominal Input Voltage	6V
Min Output Voltage	1V
Switcher Configuration	SINGLE
Duty Cycle (Max)	100%
Height	5.08mm
Length	9.81mm
Width	6.35mm
Thickness	3.9mm
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free
Factory Lead Time	1 Week
Lifecycle Status	ACTIVE (Last Updated: 4 days ago)
Mounting Type	Through Hole

TL5001CP Overview

Capsuled in the 8-DIP (0.300, 7.62mm) package, the switching controller can be used for a wide range of applications. It is sufficient to generate 1 outputs with this dc motor controller. PMIC is packaged in a solid enclosure of Tube. It is capable of handling Transistor Driver dc switching's outputs (s). Voltages 3.6V~40V are the dc control's supply voltage and operating voltage, respectively. Suitable for a -20°C~85°C TA dc switcher. In this switching controller, the switch can be set to 20kHz~500kHz. As it has a Through Hole value, it can be used for general dc dc regulator. Featured in the dcdc regulator is Dead Time Control, Frequency Control which allows efficient switching control. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. There are a DUAL terminal on the switching converters. Different dc switching's functions can be applied to 8 terminations. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. DC switcher's input voltageis set to 6V. In addition to "TL5001", there are other relevant dc to dc converter ics you can find. Switching converter has a total of 8 pins. Statistically, DC regulator outputs 50V volts. normally, the dc dc regulator's output current is 20mA, which you should keep in mind when starting a project. A frequency of 500kHz is set for the switching controller. In dormant mode, 1.1mA is used. Input voltage can be set to 6V for nominal working status. The dc switcher's maximum input voltage is 40V; users must limit it accordingly. Voltage 3.6V is necessary for the supply. An output current greater than 3A cannot be provided by the dc switcher. Depending on the datasheet, the switching converter can output 50V volts at its peak. Neither the voltage controller's lowest voltage output 1Vr its highest voltage output is less than 1V. There is a possibility of damage to the component if the switching voltage regulators current exceeds 2.1mA.