TL5001IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Base Part Number | TL5001 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 50V |
| Output Type | Transistor Driver |
| Max Output Current | 3A |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 6V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20mA |
| Voltage - Supply (Vcc/Vdd) | 3.6V~40V |
| Quiescent Current | 1.1mA |
| Control Features | Dead Time Control, Frequency Control |
| Max Output Voltage | 50V |
| Topology | Buck, Boost, Flyback |
| Min Input Voltage | 3.6V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 20kHz~500kHz |
| Max Input Voltage | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 1V |
| Switcher Configuration | SINGLE |
| Max Frequency | 500kHz |
| Duty Cycle (Max) | 100% |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL5001IDR Overview
It comes in a 8-SOIC (0.154, 3.90mm Width) package, so switching controller can be used for most applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. A solid enclosure of Tape & Reel (TR) surrounds pmic. A total of Transistor Driver dc switching's outputs can be handled by it. 3.6V~40V is the supply voltage and the operating voltage of the dc control. Work well in dc switchers with a -40°C~85°C TA. Switching can be done at 20kHz~500kHz with this switching controller. The Surface Mount value makes it suitable for general dc dc regulator. Featured in the dcdc regulator is Dead Time Control, Frequency Control which allows efficient switching control. A SWITCHING CONTROLLER analog IC is connected to the switch converters. There are a DUAL terminal on the switching converters. The 8 terminations can be used for a wide range of dc switching. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. DC switcher's input voltageis set to 6V. A search for "TL5001" will reveal other relevant dc to dc converter ics. There are a total of 8 pins on switching converter. A 50V voltage of DC regulator was detected in the test statistics. You should note that the dc dc regulator's usual output current is 20mA. It is estimated that this dc regulatorhas a maximum frequency of 500kHz. Users should apply 40V to operate the voltage regulator dc to dc safely and reliably. As long as the dc switching is in a dormant state, it utilizes 1.1mA. The dc switcher's maximum input voltage is 40V, so users must limit the voltage accordingly. 3.6V is the required supply voltage. An output current greater than 3A cannot be provided by the dc switcher. The datasheet indicates that the switching converter can output 50V volts at its maximum. 1V voltage output is lower than 1V.
TL5001IDR Features
Transistor Driver Outputs
Switching Frequency: 20kHz~500kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
TL5001IDR Applications
There are a lot of Texas Instruments TL5001IDR DC to DC converter applications.
- Planers
- Grinders
- Constant current circuits
- Remotely powered electric motors
- Smart grid
- Automation technology
- Direct power supply system
- Various precision measuring detectors
- CMM
- Product testing
