TL5002CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -20°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 500kHz |
| Base Part Number | TL5002 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 40V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 6V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 21mA |
| Voltage - Supply (Vcc/Vdd) | 3.6V~40V |
| Control Features | Dead Time Control, Frequency Control |
| Input Voltage (Min) | 3.6V |
| Topology | Boost, Flyback |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 20kHz~500kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 100 % |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL5002CDR Overview
This switching controller fits most application requirements since it is packaged in a 8-SOIC (0.154, 3.90mm Width) package. For outputs of 1, this dc motor controller is suitable. There is a Tape & Reel (TR) solid enclosure around the pmic. It is capable of handling Transistor Driver dc switching's outputs (s). Voltages 3.6V~40V are the dc control's supply voltage and operating voltage, respectively. Workable in an dc switcher where -20°C~85°C TA is the -20°C~85°C TArm. Switching can be done at 20kHz~500kHz with this switching controller. It is suitable for general dc dc regulator when it is set to Surface Mount. Featured in the dcdc regulator is Dead Time Control, Frequency Control which allows efficient switching control. An analog IC SWITCHING CONTROLLER is connected to the switch converters. The switching converters's terminals (s) are designed at DUAL. Various 8 terminations. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. It is inputted with a DC switcher's voltage of 6V. TL5002 can be used to locate other relevant dc to dc converter ics. In total, switching converter has 8 pins. Switching converter is a type of Switching Regulator or Controllers in particular. The minimum input voltage of the dc dc voltage regulator should be 3.6V. Test statistics indicate DC regulator outputs 40V voltage. If you start a project, note down the dc dc regulator's usual output current of 21mA. The duty cycle of the voltage regulator dc to dc can be set to 100 % on power-up or power-down to ensure reliability. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. Switching controller operates at 500kHz Hz. To run the voltage regulator dc to dc safely and reliably, users should apply 40V to the voltage regulator dc to dc.
TL5002CDR Features
Transistor Driver Outputs
Switching Frequency: 20kHz~500kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 100 %
Frequency: 500kHz
TL5002CDR Applications
There are a lot of Texas Instruments TL5002CDR DC to DC converter applications.
- Domestic water pumps
- Gear/thread machining machines
- Precision electronic equipment
- Smoke exhaust equipment
- USB circuits
- Motor controller circuits
- Electrical distribution systems
- Wide-range voltage regulation circuits
- Drilling machines
- Thermal power
