TL594IDR
| Parameters | |
|---|---|
| Base Part Number | TL594 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 40V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 7V~40V |
| Control Features | Dead Time Control, Frequency Control |
| Input Voltage (Min) | 7V |
| Topology | Buck, Boost, Flyback, Forward Converter, Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 1kHz~300kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 200ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 45 ns |
| Max Duty Cycle | 45 % |
| Duty Cycle (Max) | 97% |
| Output Phases | 1 |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 11 hours ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 15V |
| Frequency | 300kHz |
TL594IDR Overview
This switching controller fits most application requirements since it is packaged in a 16-SOIC (0.154, 3.90mm Width) package. There is enough capacity in the dc motor controller to generate the output for the 2 input. There is a Tape & Reel (TR) solid enclosure around the pmic. Transistor Driver dc switching's outputs (s) can be handled by it. 7V~40V is the operating voltage and supply voltage of the dc control. Workable in an dc switcher where -40°C~85°C TA is the -40°C~85°C TArm. Using this switching controller, it is possible to switch at 1kHz~300kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. In order to control switching efficiently, the dcdc regulator features Dead Time Control, Frequency Control. A SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. The switching converters's terminal (s) are designed at DUAL . Various 16 terminations. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. DC switcher's input voltageis 15V volts. TL594 can be searched for other relevant dc to dc converter ics. 16 pins are on switching converter. Specially, switching converter corresponds to type Switching Regulator or Controllers. It is recommended that the dc dc voltage regulator's minimum input voltage be 7V. Test statistics indicate DC regulator outputs 40V voltage. In most cases, the dc dc regulator's output current is 200mA. This information should be noted when you begin working with the component. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 45 % during power-up and power-down. A frequency of 300kHz is set for the switching controller. There must be a voltage supply of 15V volts.
TL594IDR Features
Transistor Driver Outputs
Switching Frequency: 1kHz~300kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 45 %
Frequency: 300kHz
TL594IDR Applications
There are a lot of Texas Instruments TL594IDR DC to DC converter applications.
- Plate bending machines
- Linear guide
- Sink circuits
- Household control circuits
- Automatic plug-in machines
- Nuclear power plants
- Computed tomography (CT)
- Access control systems
- Planers
- Computer rooms
