TL594IPWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 15V |
| Frequency | 300kHz |
| Base Part Number | TL594 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 40V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 7V~40V |
| Quiescent Current | 12.4mA |
| Control Features | Dead Time Control, Frequency Control |
| Input Voltage (Min) | 7V |
| Topology | Buck, Boost, Flyback, Forward Converter, Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 1kHz~300kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 200ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 45 ns |
| Max Duty Cycle | 45 % |
| Duty Cycle (Max) | 97% |
| Output Phases | 1 |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL594IPWR Overview
With a 16-TSSOP (0.173, 4.40mm Width) package, the switching controller is suitable for a wide range of applications. It is sufficient to generate 2 outputs with this dc motor controller. PMIC is packaged in a solid enclosure of Cut Tape (CT). Transistor Driver dc switching's outputs (s) can be handled by it. This dc control has a supply voltage and operating voltage of 7V~40V. Suitable for working in an dc switcher that has a -40°C~85°C TA. With this switching controller, you can switch at 1kHz~300kHz. dc dc regulator is made easier with Surface Mount. To ensure efficient switching, this dcdc regulator features a Dead Time Control, Frequency Control. A SWITCHING CONTROLLER analog IC is connected to the switch converters. There are a terminal (s) on the switching converters that are designed at DUAL. An array of 16 terminations of dc switching. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's voltage input is 15V. Other relevant dc to dc converter ics will be returned if you search "TL594". 16 pins are present on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. An input voltage of 7V is the minimum required for the dc dc voltage regulator. Statistically, DC regulator outputs 40V volts. In most cases, the dc dc regulator's output current is 200mA. This information should be noted when you begin working with the component. A duty cycle set at 45 % ensures voltage regulator dc to dc reliability during power-on and power-off. There is 300kHz frequency setting on the switching controller. In a dormant state, the dc switching uses 12.4mA. Switching controller is necessary to supply a voltage of 15V.
TL594IPWR Features
Transistor Driver Outputs
Switching Frequency: 1kHz~300kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 45 %
Frequency: 300kHz
TL594IPWR Applications
There are a lot of Texas Instruments TL594IPWR DC to DC converter applications.
- Electrical distribution systems
- Geothermal power
- Domestic water pumps
- Digital display device
- Medical equipment
- Wide-range voltage regulation circuits
- Packaging
- Elevator lighting
- Industrial controllers
- USB circuits
