TLC071CD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLC071 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Number of Elements | 1 |
| Operating Supply Current | 2.1mA |
| Nominal Supply Current | 2.9mA |
| Power Dissipation | 710mW |
| Output Current | 57mA |
| Slew Rate | 19V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1.5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~16V ±2.25V~8V |
| Output Current per Channel | 57mA |
| Input Offset Voltage (Vos) | 1.9mV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 390μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 10MHz |
| Max I/O Voltage | 1.9mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC071CD Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. It has 8 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 1.9mV. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, op amp ranges 0°C~70°C. As long as the supply current of the chip does not exceed 2.1mA, this op amp ic can operate. Keeping the voltage gain at 120dB is the best course of action. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. The operating supply voltage of instrumentation amplifier is rated 8V voltage.
TLC071CD Features
8 Pins
supply voltage of 5V
120dB voltage gain
TLC071CD Applications
There are a lot of Texas Instruments TLC071CD Instrumentational OP Amps applications.
- E-book readers
- Signal operation
- Multiplication circuits
- Industrial applications including automation
- Broadcasting
- Car stereo
- Differentiator circuits
- Industrial control system
- Portable electronic products powered by batteries
- Band-pass filter
