TLC071IP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TLC071 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Number of Circuits | 1 |
| Operating Supply Current | 2.1mA |
| Nominal Supply Current | 2.9mA |
| Output Current | 57mA |
| Slew Rate | 19V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1.5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~16V ±2.25V~8V |
| Output Current per Channel | 57mA |
| Input Offset Voltage (Vos) | 390μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 10MHz |
| Max I/O Voltage | 1.9mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC071IP Overview
It is packaged in an 8-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tube case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. Please take in mind that this instrumentation amplifier should be run at 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are available on the instrumentation amplifier. Regarding input offset voltage, op amp rates 390μV. This electronic component is recommended to be mounted using the mounting type Through Hole. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . An 2.1mA volt supply current is needed for this linear amplifier to operate. 120dB should remain the voltage gain. This op amp ic has 1 circuits. The operating supply voltage of the buffer op amp is rated at 8V.
TLC071IP Features
8 Pins
supply voltage of 5V
120dB voltage gain
TLC071IP Applications
There are a lot of Texas Instruments TLC071IP Instrumentational OP Amps applications.
- Addition operation circuits
- pH (acidity)
- Multiplication circuits
- Power generator
- Proportional counter tubes
- Measurements of Wheatstone bridge
- Switching amplifier
- Voltage regulation circuit
- Large motor controllers
- Integrator circuits
