TLC072IDGNR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 2.37W |
| Technology | BIMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLC072 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Operating Supply Current | 2.1mA |
| Nominal Supply Current | 5.8mA |
| Power Dissipation | 2.37W |
| Output Current | 57mA |
| Slew Rate | 19V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1.5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~16V ±2.25V~8V |
| Output Current per Channel | 57mA |
| Input Offset Voltage (Vos) | 1.9mV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 17V |
| Voltage - Input Offset | 390μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 10MHz |
| Max I/O Voltage | 1.9mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC072IDGNR Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad case. Op amps are General Purpose types of amplifier on the chip. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. There have been a total of 8 terminations over the past year. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. An 8-pin op amp ic is included in the package. Op amp ic rates 1.9mV for input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 2.1mA, this op amp ic can operate. There should be no change in the voltage gain. There are 2 elements in this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 8V. For packing the buffer amplifier, the TR-axis is adopted.
TLC072IDGNR Features
8 Pins
supply voltage of 5V
120dB voltage gain
TLC072IDGNR Applications
There are a lot of Texas Instruments TLC072IDGNR Instrumentational OP Amps applications.
- Television broadcasting equipment
- Division circuits
- Exponential operation circuits
- Portable media players
- Television
- Test equipment
- Blood pressure sensors
- Fast A/D and D/A converters
- Band-stop filter
- Communication device
