TLC072QDRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC072 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Operating Supply Current | 2.1mA |
| Nominal Supply Current | 5.8mA |
| Power Dissipation | 710mW |
| Output Current | 57mA |
| Slew Rate | 19V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1.5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~16V ±2.25V~8V |
| Output Current per Channel | 57mA |
| Input Offset Voltage (Vos) | 1.9mV |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 17V |
| Voltage - Input Offset | 390μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 10MHz |
| Max I/O Voltage | 1.9mV |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC072QDRQ1 Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. Op amps are General Purpose types of amplifier on the chip. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. In this case, there are 8 pins on the board. Please take in mind that op amp should be run at 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 8 pins are located on the operational amplifiers. There is an input offset voltage of 1.9mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~125°C. The buffer amplifier is capable of operating from a supply current of 2.1mA . 120dB should remain the voltage gain. 2 elements make up the design of this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 8V voltage. A TR-shaped amplifier is used to pack the buffer amps. The Automotive, AEC-Q100 stands for the buffer op amp's serial number.
TLC072QDRQ1 Features
8 Pins
supply voltage of 5V
120dB voltage gain
TLC072QDRQ1 Applications
There are a lot of Texas Instruments TLC072QDRQ1 Instrumentational OP Amps applications.
- Non-polarized electrodes
- Medical imaging
- Power generator
- Communication
- Commercial audio systems
- Inverse/same-phase proportional circuit
- Differentiator circuits
- Weak signal detection
- Displayers for aircraft and air transportation control systems
- Multimedia playback equipment
