TLC2201IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLC2201 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Elements | 1 |
| Operating Supply Current | 1.1mA |
| Nominal Supply Current | 1.5mA |
| Power Dissipation | 725mW |
| Output Current | 50mA |
| Slew Rate | 2.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4.6V~16V ±2.3V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 1.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1900 kHz |
| Voltage Gain | 109.97dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 100μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.9MHz |
| Max I/O Voltage | 500μV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC2201IDR Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. The number of terminations approaches 8. In total, there are 8 pins on this op amp ic. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 8 pins on it. The input offset voltage is 500μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. Operational amplifier can operate supply current at 1.1mA. Op amp is a member of the 109.97dB's 109.97dB family. On the output type, there are Rail-to-Rail different types of op amps. There is an operating supply voltage rating of 1 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 8V. The instrumentation amplifier is packed in the form of TR. The LinCMOS? stands for the buffer op amp's serial number.
TLC2201IDR Features
8 Pins
supply voltage of 5V
109.97dB voltage gain
Output Type: Rail-to-Rail
TLC2201IDR Applications
There are a lot of Texas Instruments TLC2201IDR Instrumentational OP Amps applications.
- Precision measurement
- Portable media players
- High/low-pass filter circuit
- Automotive sensors
- Integrator circuits
- Portable electronic products powered by batteries
- Voltage regulation circuit
- Inverse/same-phase proportional circuit
- Vehicle electronics
- Signal operation
