TLC2202AMJGB
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Package / Case | CDIP |
| Surface Mount | NO |
| Number of Pins | 8 |
| Packaging | Rail/Tube |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Pin Count | 8 |
| Number of Elements | 2 |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 4.6V |
| Power Dissipation | 1.05W |
| Slew Rate | 2.5 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Input Offset Voltage (Vos) | 500μV |
| Gain Bandwidth Product | 1.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1900 kHz |
| Voltage Gain | 109.97dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 8V |
| Low-Bias | YES |
| Micropower | YES |
| Min Dual Supply Voltage | 2.3V |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 5.08mm |
| Length | 9.6mm |
| Width | 6.67mm |
| Thickness | 4.57mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
TLC2202AMJGB Overview
Packaged in a CDIP case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. Linear amplifier is delivered in a Rail/Tube case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. The input offset voltage is 500μV. 109.97dB should be the voltage gain. This instrumentation amplifier cannot operate below -55°C degrees Celsius. It should only be used at temperatures up above 125°C. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. I would like to point out that this electrical component is capable of working from a voltage below 16V as far as the power supply is concerned. A voltage of 4.6V or higher is recommended for the linear amplifier's supply voltage. You should conduct this electronic component under the dual supply voltage of 8V.
TLC2202AMJGB Features
8 Pins
supply voltage of 5V
109.97dB voltage gain
TLC2202AMJGB Applications
There are a lot of Texas Instruments TLC2202AMJGB Instrumentational OP Amps applications.
- Micro signal measurement
- ECG equipment
- Voltage regulation circuit
- Video data acquisition
- Broadcasting
- Radar
- Proportional operation circuits
- Video computer boards
- Home audio systems
- Signal operation
