TLC2252CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC2252 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Operating Supply Current | 80μA |
| Nominal Supply Current | 125μA |
| Power Dissipation | 724mW |
| Output Current | 50mA |
| Slew Rate | 0.12V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4.4V~16V ±2.2V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 200 kHz |
| Gain Bandwidth Product | 210kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 200 kHz |
| Voltage Gain | 124.61dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 200 kHz |
| Max I/O Voltage | 1.5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC2252CDR Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are available on the instrumentation amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 1.5mV. This electronic part is best mounted with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureUsing an 80μA supply current, this operational amplifier ics can be operated. Maintain 124.61dB as the voltage gain. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. 2 elements make up the design of this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 8V. It is used TR to pack the op amps. Buffer op amp series numbers are indicated by the LinCMOS?.
TLC2252CDR Features
8 Pins
supply voltage of 5V
124.61dB voltage gain
Output Type: Rail-to-Rail
TLC2252CDR Applications
There are a lot of Texas Instruments TLC2252CDR Instrumentational OP Amps applications.
Voltage regulation circuit
Weak signal detection
Image computer boards
Multimedia playback equipment
Information processing
Comparator
ECG equipment
Logarithmic operation circuits
Video conversion and routing
earphone
