TLC2252CPWR
| Parameters | |
|---|---|
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 200 kHz |
| Max I/O Voltage | 1.5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.2mm |
| Length | 3mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 525mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLC2252 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Operating Supply Current | 80μA |
| Nominal Supply Current | 125μA |
| Power Dissipation | 525mW |
| Output Current | 50mA |
| Slew Rate | 0.12V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4.4V~16V ±2.2V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 200 kHz |
| Gain Bandwidth Product | 210kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 200 kHz |
| Voltage Gain | 124.61dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
TLC2252CPWR Overview
There is a 8-TSSOP (0.173, 4.40mm Width) case in which the instrumentation amplifier is packaged. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Cut Tape (CT) case. During the past two weeks, there have been close to 8 terminations. The pins on this board total to 8 in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are included on the operational amplifiers. The input offset voltage is 1.5mV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . Using a supply current of 80μA , this buffer op amp will be able to operate. 124.61dB should remain the voltage gain. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The total number of elements in this buffer amplifier is 2. The operating supply voltage of the buffer op amp is rated at 8V. As a result of this, the buffer amplifier is packed in TR. LinCMOS? corresponds to linear amplifier's series.
TLC2252CPWR Features
8 Pins
supply voltage of 5V
124.61dB voltage gain
Output Type: Rail-to-Rail
TLC2252CPWR Applications
There are a lot of Texas Instruments TLC2252CPWR Instrumentational OP Amps applications.
- Signal filtering
- Division circuits
- Instrumentation
- ECG equipment
- Integrator circuits
- Ultrasound transducers
- RF cable systems
- Fission chambers
- PDA
- Blood pressure sensors
