TLC2252ID
| Parameters | |
|---|---|
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4.4V~16V ±2.2V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 200 kHz |
| Gain Bandwidth Product | 210kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 200 kHz |
| Voltage Gain | 124.61dB |
| Average Bias Current-Max (IIB) | 0.001μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 200 kHz |
| Max I/O Voltage | 1.5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC2252 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Channels | 2 |
| Operating Supply Current | 80μA |
| Nominal Supply Current | 125μA |
| Power Dissipation | 724mW |
| Output Current | 50mA |
| Slew Rate | 0.12V/μs |
| Architecture | VOLTAGE-FEEDBACK |
TLC2252ID Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. Buffer amps of this type are called General Purpose-types. There is a Tube case that is delivered with the instrumentation amplifiers. The number of terminations approaches 8. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 8-pin op amp ic is included in the package. In terms of input offset voltage, operational amplifier rates 1.5mV. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 80μA, this op amp ic can operate. 124.61dB should remain the voltage gain. Instrumentation amplifier has 2 channels on it. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 8V. Buffer op amp series numbers are indicated by the LinCMOS?.
TLC2252ID Features
8 Pins
supply voltage of 5V
124.61dB voltage gain
Output Type: Rail-to-Rail
TLC2252ID Applications
There are a lot of Texas Instruments TLC2252ID Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Non-polarized electrodes
- Car stereo
- Portable electronic products powered by batteries
- Industrial applications including automation
- Precision measurement
- Communication
- Medical imaging
- Video conversion and routing
- Television
