TLC2254ID
| Parameters | |
|---|---|
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 200 kHz |
| Max I/O Voltage | 1.5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 950mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLC2254 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Channels | 4 |
| Operating Supply Current | 160μA |
| Nominal Supply Current | 250μA |
| Power Dissipation | 950mW |
| Output Current | 50mA |
| Slew Rate | 0.12V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4.4V~16V ±2.2V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 200 kHz |
| Gain Bandwidth Product | 210kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 200 kHz |
| Voltage Gain | 124.61dB |
| Average Bias Current-Max (IIB) | 0.001μA |
TLC2254ID Overview
Packaged in a 14-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp of this type is a General Purpose-type. Linear amplifier is delivered in a Tube case. During the past two weeks, there have been close to 14 terminations. In total, there are 14 pins on this op amp ic. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 14 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 1.5mV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . As long as the supply current of the chip does not exceed 160μA, this op amp ic can operate. There should be no change in the voltage gain at 124.61dB. On the buffer amps, there are 4 channels that can be used. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 8V. In this case, LinCMOS? represents the instrumentation amplifiers' series number.
TLC2254ID Features
14 Pins
supply voltage of 5V
124.61dB voltage gain
Output Type: Rail-to-Rail
TLC2254ID Applications
There are a lot of Texas Instruments TLC2254ID Instrumentational OP Amps applications.
- Test and measurement instruments
- Logarithmic operation circuits
- Multimedia playback equipment
- Portable media players
- Biopotential
- RF cable systems
- Differentiator circuits
- Instrumentation
- Automation control systems
- Automotive sensors
