TLC2262ID
| Parameters | |
|---|---|
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC2262 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Channels | 2 |
| Operating Supply Current | 425μA |
| Nominal Supply Current | 500μA |
| Power Dissipation | 725mW |
| Output Current | 50mA |
| Slew Rate | 0.55V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4.4V~16V ±2.2V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Bandwidth | 820 kHz |
| Gain Bandwidth Product | 730kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 710 kHz |
| Voltage Gain | 114.81dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 300μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 820 kHz |
| Max I/O Voltage | 2.5mV |
TLC2262ID Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used to deliver the buffer op amp. During the past two weeks, there have been close to 8 terminations. The total number of pins on linear amplifier is 8. I would like to remind you that this buffer op amp should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The op amp ic has an array of 8 pins on it. As far as the input offset voltage is concerned, linear amplifier rates at 2.5mV. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Using an 425μA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain. There are 2 channels on the operational amplifiers. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of instrumentation amplifier is rated 8V voltage. This buffer amplifier is assigned within the LinCMOS? series by its manufacturer.
TLC2262ID Features
8 Pins
supply voltage of 5V
114.81dB voltage gain
Output Type: Rail-to-Rail
TLC2262ID Applications
There are a lot of Texas Instruments TLC2262ID Instrumentational OP Amps applications.
- High gain DC amplifier
- single/dual op amp sum and difference circuits
- Professional videography
- Inverse/same-phase proportional circuit
- Integrator circuits
- Subtraction operation circuits
- Displayers for aircraft and air transportation control systems
- Video data acquisition
- Communication device
- Ultrasound transducers
