TLC2274MDRG4
| Parameters | |
|---|---|
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLC2274 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Elements | 4 |
| Operating Supply Current | 4.8mA |
| Nominal Supply Current | 6mA |
| Output Current | 50mA |
| Slew Rate | 3.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4.4V~16V ±2.2V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Gain Bandwidth Product | 2.25MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 2250 kHz |
| Voltage Gain | 104.86dB |
| Average Bias Current-Max (IIB) | 0.0008μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 300μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Max I/O Voltage | 2.5mV |
| Wideband | NO |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
TLC2274MDRG4 Overview
In order to protect the op amps, a 14-SOIC (0.154, 3.90mm Width) case is used. An op amp of this type is a General Purpose-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 14. A total of 14 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. An 14-pin op amp ic is included in the package. Op amp ic rates 2.5mV for input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. The buffer amplifier functions well at -55°C~125°C as far as operating temperature is concerned. You can run this op amp ic on 4.8mA . Op amp is a member of the 104.86dB's 104.86dB family. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. A voltage rating of 4 is indicated for the op amp's operating supply voltage. The operating supply voltage of the buffer op amp is rated at 8V. For the packing of the instrumentation amplifier, TR is adopted. The LinCMOS? indicates the series number of the op amp.
TLC2274MDRG4 Features
14 Pins
supply voltage of 5V
104.86dB voltage gain
Output Type: Rail-to-Rail
TLC2274MDRG4 Applications
There are a lot of Texas Instruments TLC2274MDRG4 Instrumentational OP Amps applications.
- earphone
- Power transmission
- Scintillation detectors
- Signal filtering
- Inverse/same-phase proportional circuit
- Mobile phone
- Large motor controllers
- High/low-pass filter circuit
- E-book readers
- Weak signal detection
