TLC252BCD
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC252 |
| Pin Count | 8 |
| Power Supplies | 1.4/16V |
| Number of Circuits | 2 |
| Operating Supply Current | 1.9mA |
| Nominal Supply Current | 4mA |
| Slew Rate | 5.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.6pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~16V ±0.7V~8V |
| Input Offset Voltage (Vos) | 290μV |
| Bandwidth | 1.7MHz |
| Gain Bandwidth Product | 2.2MHz |
| Unity Gain BW-Nom | 1700 kHz |
| Voltage Gain | 87.23dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.7MHz |
| Max I/O Voltage | 2mV |
| Power | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC252BCD Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. There is a growing number of terminations approaching the number of 8. It consists of a total of 8 pins in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are included on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 290μV. Surface Mount is the recommended mounting type of operational amplifiers. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. An 1.9mA volt supply current is needed for this linear amplifier to operate. 87.23dB should be the voltage gain. A linear amplifier like this has 2 circuits on it. The LinCMOS? stands for the buffer op amp's serial number.
TLC252BCD Features
8 Pins
supply voltage of 5V
87.23dB voltage gain
TLC252BCD Applications
There are a lot of Texas Instruments TLC252BCD Instrumentational OP Amps applications.
- MP3
- Integrator circuits
- ECG equipment
- Addition operation circuits
- Scintillation detectors
- Power control
- High-frequency data acquisition systems
- Signal operation
- Proportional counter tubes
- Navigation
