TLC254CNE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Package / Case | PDIP |
| Surface Mount | NO |
| Number of Pins | 14 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | Operational Amplifier |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Pin Count | 14 |
| Operating Supply Voltage | 8V |
| Temperature Grade | COMMERCIAL |
| Number of Channels | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 1.4V |
| Operating Supply Current | 4.5mA |
| Nominal Supply Current | 8mA |
| Slew Rate | 3.6 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 60pA |
| Input Offset Voltage (Vos) | 1.1mV |
| Bandwidth | 1.7MHz |
| Gain Bandwidth Product | 1.7MHz |
| Unity Gain BW-Nom | 1700 kHz |
| Voltage Gain | 87.23dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 8V |
| Low-Bias | YES |
| Micropower | NO |
| Min Dual Supply Voltage | 700mV |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.7MHz |
| Max I/O Voltage | 10mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.0006μA |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
TLC254CNE4 Overview
The linear amplifier is packaged in a PDIP case. This is a OPERATIONAL AMPLIFIER type op amp. A total of 14 terminations have been reported in the past few weeks. Linear amplifier has a total of 14 pins. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. Linear amplifier includes 14 pins. Regarding input offset voltage, op amp rates 1.1mV. As long as the supply current of the chip does not exceed 4.5mA, this op amp ic can operate. 87.23dB should remain the voltage gain. Op amp ic has 4 channels. This op amp needs to be operated at a temperature of not less than 0°C degrees Celsius in order to function properly. You should not use op amp above 70°C . The operating supply voltage of instrumentation amplifier is rated 8V voltage. To pack the operational amplifier ics, TUBE is adopted as the packing method. The electrical part is capable of being powered by a voltage of under 16V, which means that it can be used with any voltage supply. Over 1.4V is a recommended supply voltage for buffer ampsAs a rule of thumb, you should conduct this electronic part under a dual voltage supply of 8V volts.
TLC254CNE4 Features
14 Pins
supply voltage of 5V
87.23dB voltage gain
TLC254CNE4 Applications
There are a lot of Texas Instruments TLC254CNE4 Instrumentational OP Amps applications.
- High input resistance broadband
- Voltage regulation circuit
- Weak signal detection
- Radiation thermometry transducers
- Automatic control
- Blood pressure sensors
- Multimedia playback equipment
- Laptop
- Weighing systems
- Vehicle electronics
