TLC2652CP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLC2652 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Number of Channels | 1 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 2.4mA |
| Power Dissipation | 1W |
| Slew Rate | 3.1V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 4pA |
| Voltage - Supply, Single/Dual (±) | 3.8V~16V ±1.9V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 3μV |
| Bandwidth | 1.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1900 kHz |
| Voltage Gain | 150dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 0.6μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 1.9MHz |
| Max I/O Voltage | 3μV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC2652CP Overview
Packaged in a 8-DIP (0.300, 7.62mm) case, the buffer op amp is ready to use. Zero-Drift-type instrumentation amplifiers are used in this application. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. Please take in mind that this instrumentation amplifier should be run at 5V. It should be noted that this op amp is a type of Operational Amplifier device. It has 8 pins that make up the linear amplifier. With regard to input offset voltage, instrumentation amplifier is rated at 3μV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. With regard to operating temperature, op amp ranges 0°C~70°C. An 1.5mA volt supply current is needed for this linear amplifier to operate. Maintain 150dB as the voltage gain. There are a total of 1 channels available on the op amps. Op amp has total of 2 elements. The operating supply voltage of the buffer op amp is rated at 8V. The LinCMOS? indicates the series number of the op amp.
TLC2652CP Features
8 Pins
supply voltage of 5V
150dB voltage gain
TLC2652CP Applications
There are a lot of Texas Instruments TLC2652CP Instrumentational OP Amps applications.
- Signal amplification
- Industrial control system
- single/dual op amp sum and difference circuits
- Vehicle electronics
- Semiconductor detectors
- Large motor controllers
- Exponential operation circuits
- Video conversion and routing
- MP3
- Cinema or auditorium audio system
