TLC2654I-8DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | TLC2654 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 8V |
| Number of Elements | 1 |
| Power Supplies | +-5V |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 2.4mA |
| Power Dissipation | 725mW |
| Slew Rate | 3.7V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 105 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | 4.6V~16V ±2.3V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 20μV |
| Bandwidth | 1.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1900 kHz |
| Voltage Gain | 155dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 5μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.9MHz |
| Max I/O Voltage | 20μV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC2654I-8DR Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this op amp is a type of Operational Amplifier device. Linear amplifier includes 8 pins. The input offset voltage is 20μV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . Operational amplifier can operate supply current at 1.5mA. There should be no change in the voltage gain at 155dB. The linear amplifier consists of 1 different elements in total. The operating supply voltage of instrumentation amplifier is rated 8V voltage. The instrumentation amplifier is packed in the form of TR. Buffer op amp series numbers are indicated by the LinCMOS?.
TLC2654I-8DR Features
8 Pins
supply voltage of 5V
155dB voltage gain
TLC2654I-8DR Applications
There are a lot of Texas Instruments TLC2654I-8DR Instrumentational OP Amps applications.
- pH (acidity)
- Automotive sensors
- Signal filtering
- Ultrasound transducers
- Television
- Biopotential
- Inverse/same-phase proportional circuit
- Video data acquisition
- Band-pass filter
- Power transmission
