TLC271CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLC271 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 950μA |
| Nominal Supply Current | 2mA |
| Power Dissipation | 725mW |
| Slew Rate | 5.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.7pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1.7MHz |
| Gain Bandwidth Product | 2.2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 87.23dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | YES |
| Nominal Gain Bandwidth Product | 1.7MHz |
| Max I/O Voltage | 10mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC271CDR Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 8. It consists of a total of 8 pins in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. An 8-pin op amp ic is included in the package. In terms of the input offset voltage, instrumentation amplifier rates at 10mV. This electrical part should be mounted using type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . An 950μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. There are 1 channels on the operational amplifiers. An buffer amplifier is packed in a TR-shape according to the design. In this case, LinCMOS? represents the instrumentation amplifiers' series number.
TLC271CDR Features
8 Pins
supply voltage of 5V
87.23dB voltage gain
TLC271CDR Applications
There are a lot of Texas Instruments TLC271CDR Instrumentational OP Amps applications.
- Weak signal detection
- Test and measurement instruments
- PDA
- Micro signal measurement
- Video conversion and routing
- Power generator
- Fission chambers
- Automatic control
- MP3
- Comparator
