Parameters | |
---|---|
Factory Lead Time | 1 Week |
Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
Mounting Type | Surface Mount |
Package / Case | 8-SOIC (0.154, 3.90mm Width) |
Surface Mount | YES |
Number of Pins | 8 |
Operating Temperature | 0°C~70°C |
Packaging | Tape & Reel (TR) |
Series | LinCMOS™ |
JESD-609 Code | e4 |
Pbfree Code | yes |
Part Status | Active |
Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
Number of Terminations | 8 |
ECCN Code | EAR99 |
Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory | Operational Amplifier |
Packing Method | TR |
Terminal Position | DUAL |
Terminal Form | GULL WING |
Peak Reflow Temperature (Cel) | 260 |
Number of Functions | 2 |
Supply Voltage | 5V |
Base Part Number | TLC272 |
Pin Count | 8 |
Power Supplies | 3/16V |
Number of Channels | 2 |
Operating Supply Current | 1.9mA |
Nominal Supply Current | 4mA |
Power Dissipation | 725mW |
Slew Rate | 5.3V/μs |
Architecture | VOLTAGE-FEEDBACK |
Amplifier Type | General Purpose |
Common Mode Rejection Ratio | 65 dB |
Current - Input Bias | 0.7pA |
Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
Output Current per Channel | 30mA |
Input Offset Voltage (Vos) | 10mV |
Bandwidth | 1.7MHz |
Gain Bandwidth Product | 2.2MHz |
Unity Gain BW-Nom | 2000 kHz |
Voltage Gain | 87.23dB |
Average Bias Current-Max (IIB) | 0.00006μA |
Low-Offset | NO |
Frequency Compensation | YES |
Voltage - Input Offset | 1.1mV |
Low-Bias | YES |
Micropower | NO |
Bias Current-Max (IIB) @25C | 0.00006μA |
Programmable Power | NO |
Nominal Gain Bandwidth Product | 1.7MHz |
Max I/O Voltage | 10mV |
Input Offset Current-Max (IIO) | 0.00006μA |
Height | 1.75mm |
Length | 4.9mm |
Width | 3.91mm |
Thickness | 1.58mm |
Radiation Hardening | No |
REACH SVHC | No SVHC |
RoHS Status | ROHS3 Compliant |
Lead Free | Lead Free |
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. Op amps are General Purpose types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 8. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. There are 8 pins on this chip. Op amp rates 10mV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureOperational amplifier can operate supply current at 1.9mA. 87.23dB should be the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. It is used TR to pack the op amps. The LinCMOS? stands for the buffer op amp's serial number.
8 Pins
supply voltage of 5V
87.23dB voltage gain
There are a lot of Texas Instruments TLC272CDR Instrumentational OP Amps applications.
Communication device
Band-pass filter
Medical imaging
Power generator
Communication
Blood pressure sensors
Digital cameras
Commercial audio systems
RF cable systems
Mobile phone