Parameters |
Nominal Supply Current |
4mA |
Power Dissipation |
1W |
Slew Rate |
5.3V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
65 dB |
Current - Input Bias |
0.7pA |
Voltage - Supply, Single/Dual (±) |
4V~16V ±2V~8V |
Output Current per Channel |
30mA |
Input Offset Voltage (Vos) |
1.1mV |
Bandwidth |
1.7MHz |
Gain Bandwidth Product |
2.2MHz |
Unity Gain BW-Nom |
2000 kHz |
Voltage Gain |
87.23dB |
Average Bias Current-Max (IIB) |
0.00006μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00006μA |
Programmable Power |
NO |
Nominal Gain Bandwidth Product |
1.7MHz |
Max I/O Voltage |
10mV |
Input Offset Current-Max (IIO) |
0.00006μA |
Height |
5.08mm |
Length |
9.81mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mounting Type |
Through Hole |
Package / Case |
8-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
Series |
LinCMOS™ |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
TLC272 |
Pin Count |
8 |
Power Supplies |
4/16V |
Number of Channels |
2 |
Operating Supply Current |
1.4mA |
TLC272IP Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. An op amp of this type is a General Purpose-type. There is a Tube case that is delivered with the instrumentation amplifiers. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are available on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 1.1mV. For this electrical component, Through Hole is the recommended mounting type. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. Operational amplifier can operate supply current at 1.4mA. You should keep the voltage gain at 87.23dB for the time being. On the buffer amps, there are 2 channels that can be used. The LinCMOS? indicates the series number of the op amp.
TLC272IP Features
8 Pins
supply voltage of 5V
87.23dB voltage gain
TLC272IP Applications
There are a lot of Texas Instruments TLC272IP Instrumentational OP Amps applications.
- earphone
- RF cable systems
- Large motor controllers
- Inverse/same-phase proportional circuit
- Automation control systems
- High input resistance broadband
- Medical imaging
- Signal amplification
- Cinema or auditorium audio system
- ECG equipment