TLC274CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLC274 |
| Pin Count | 14 |
| Power Supplies | 3/16V |
| Number of Channels | 4 |
| Operating Supply Current | 3.8mA |
| Nominal Supply Current | 8mA |
| Power Dissipation | 950mW |
| Slew Rate | 5.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.7pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1.7MHz |
| Gain Bandwidth Product | 2.2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 87.23dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.7MHz |
| Max I/O Voltage | 10mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC274CDR Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Cut Tape (CT) case. There have been a total of 14 terminations over the past year. It consists of a total of 14 pins in total. This linear amplifier should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. In total, the buffer amplifier consists of 14 pins. Op amp ic rates 10mV for input offset voltage. This electronic component is recommended to be mounted using the mounting type Surface Mount. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. An 3.8mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 87.23dB. Instrumentation amplifier has 4 channels on it. For the packing of the instrumentation amplifier, TR is adopted. LinCMOS? corresponds to linear amplifier's series.
TLC274CDR Features
14 Pins
supply voltage of 5V
87.23dB voltage gain
TLC274CDR Applications
There are a lot of Texas Instruments TLC274CDR Instrumentational OP Amps applications.
- Communication device
- High/low-pass filter circuit
- Digital cameras
- Subtraction operation circuits
- PDA
- Division circuits
- Power generator
- Computer workstations
- Radiation thermometry transducers
- Voltage regulation circuit
