Parameters |
Voltage Gain |
87.23dB |
Average Bias Current-Max (IIB) |
0.00006μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
18V |
Voltage - Input Offset |
1.1mV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00006μA |
Programmable Power |
NO |
Nominal Gain Bandwidth Product |
1.7MHz |
Max I/O Voltage |
10mV |
Input Offset Current-Max (IIO) |
0.00006μA |
Height |
1.75mm |
Length |
8.65mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
14 |
Operating Temperature |
-55°C~125°C |
Packaging |
Tube |
Series |
LinCMOS™ |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Base Part Number |
TLC274 |
Pin Count |
14 |
Number of Elements |
4 |
Operating Supply Current |
3.8mA |
Nominal Supply Current |
8mA |
Power Dissipation |
950mW |
Slew Rate |
5.3V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
65 dB |
Current - Input Bias |
0.7pA |
Voltage - Supply, Single/Dual (±) |
4V~16V ±2V~8V |
Output Current per Channel |
30mA |
Input Offset Voltage (Vos) |
10mV |
Bandwidth |
1.7MHz |
Gain Bandwidth Product |
2.2MHz |
Unity Gain BW-Nom |
2000 kHz |
TLC274MD Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. There are two types of operational amplifiers in this circuit. Linear amplifier is delivered in a Tube case. The number of terminations is approaching the 14 mark. A total of 14 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 14 pins that make up the linear amplifier. There is an input offset voltage of 10mV for this buffer op amp. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -55°C~125°C . This op amp can operate from a supply current at 3.8mA. Maintain 87.23dB as the voltage gain. Op amp has total of 4 elements. A TR-shaped amplifier is used to pack the buffer amps. LinCMOS? corresponds to linear amplifier's series.
TLC274MD Features
14 Pins
supply voltage of 5V
87.23dB voltage gain
TLC274MD Applications
There are a lot of Texas Instruments TLC274MD Instrumentational OP Amps applications.
- High-frequency data acquisition systems
- Radiation thermometry transducers
- Measurements of Wheatstone bridge
- Information processing
- Micro signal measurement
- Portable media players
- Image computer boards
- earphone
- Large motor controllers
- Addition operation circuits