TLC274MDRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLC274 |
| Pin Count | 14 |
| Number of Elements | 4 |
| Power Supplies | 3/16V |
| Operating Supply Current | 3.8mA |
| Nominal Supply Current | 6.4mA |
| Power Dissipation | 950mW |
| Slew Rate | 5.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.7pA |
| Voltage - Supply, Single/Dual (±) | 4V~16V ±2V~8V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1.7MHz |
| Gain Bandwidth Product | 2.2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 87.23dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.7MHz |
| Max I/O Voltage | 10mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC274MDRG4 Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. Linear amplifier is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 14. The pins on this board total to 14 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. There is an input offset voltage of 10mV for this buffer op amp. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -55°C~125°C , which is a good operating temperature. Using a supply current of 3.8mA , this buffer op amp will be able to operate. 87.23dB should remain the voltage gain. The linear amplifier consists of 4 different elements in total. This linear amplifier pack is based on the TR axis. Instrumentation amplifiers are numbered by their LinCMOS? series.
TLC274MDRG4 Features
14 Pins
supply voltage of 5V
87.23dB voltage gain
TLC274MDRG4 Applications
There are a lot of Texas Instruments TLC274MDRG4 Instrumentational OP Amps applications.
- Oscilloscopes
- Differentiator circuits
- Weighing systems
- Radiation thermometry transducers
- Large motor controllers
- Fission chambers
- High/low-pass filter circuit
- Television broadcasting equipment
- Precision measurement
- Video amplifiers
