TLC27L2AID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC27 |
| Pin Count | 8 |
| Power Supplies | 4/16V |
| Number of Channels | 2 |
| Operating Supply Current | 29μA |
| Nominal Supply Current | 46μA |
| Power Dissipation | 725mW |
| Slew Rate | 0.05V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.7pA |
| Voltage - Supply, Single/Dual (±) | 4V~16V ±2V~8V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 85 kHz |
| Gain Bandwidth Product | 110kHz |
| Unity Gain BW-Nom | 130 kHz |
| Voltage Gain | 113.62dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 900μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 85 kHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC27L2AID Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. A Tube case is used to deliver the buffer op amp. The number of terminations approaches 8. In this case, there are 8 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. The op amp ic has an array of 8 pins on it. There is an input offset voltage of 5mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Using a supply current of 29μA , this buffer op amp will be able to operate. It is a member of the 113.62dB's 113.62dB family. There are a total of 2 channels available on the op amps. This buffer amplifier is assigned within the LinCMOS? series by its manufacturer.
TLC27L2AID Features
8 Pins
supply voltage of 5V
113.62dB voltage gain
TLC27L2AID Applications
There are a lot of Texas Instruments TLC27L2AID Instrumentational OP Amps applications.
- Automotive sensors
- Wireless base stations
- Signal amplification
- Exponential operation circuits
- Blood pressure sensors
- Displayers for aircraft and air transportation control systems
- Non-polarized electrodes
- Inverse/same-phase proportional circuit
- High/low-pass filter circuit
- Differentiator circuits
