banner_page

TLC27L9IN

30mA per Channel 0.7pA 65 dB Instrumentational OP Amps 0.002μA 3V~16V ±1.5V~8V TLC27 14 Pins 14-DIP (0.300, 7.62mm)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-TLC27L9IN
  • Package: 14-DIP (0.300, 7.62mm)
  • Datasheet: -
  • Stock: 901
  • Description: 30mA per Channel 0.7pA 65 dB Instrumentational OP Amps 0.002μA 3V~16V ±1.5V~8V TLC27 14 Pins 14-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Programmable Power NO
Nominal Gain Bandwidth Product 85 kHz
Max I/O Voltage 900μV
Height 5.08mm
Length 19.3mm
Width 6.35mm
Thickness 3.9mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 1 week ago)
Mounting Type Through Hole
Package / Case 14-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 14
Operating Temperature -40°C~85°C
Packaging Tube
Series LinCMOS™
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Operational Amplifier
Terminal Position DUAL
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 10V
Base Part Number TLC27
Pin Count 14
Number of Elements 4
Power Supplies 5/10V
Operating Supply Current 57μA
Nominal Supply Current 92μA
Power Dissipation 1.575W
Slew Rate 0.05V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 65 dB
Current - Input Bias 0.7pA
Voltage - Supply, Single/Dual (±) 3V~16V ±1.5V~8V
Output Current per Channel 30mA
Input Offset Voltage (Vos) 900μV
Bandwidth 85 kHz
Gain Bandwidth Product 110kHz
Unity Gain BW-Nom 110 kHz
Voltage Gain 113.62dB
Average Bias Current-Max (IIB) 0.002μA
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 18V
Voltage - Input Offset 210μV
Low-Bias YES
Micropower YES

TLC27L9IN Overview


In order to protect the op amps, a 14-DIP (0.300, 7.62mm) case is used. This is a General Purpose type op amp. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. There is a growing number of terminations approaching the number of 14. The pins on this board total to 14 in total. The linear amplifier should be run at 10V at all times, so please keep that in mind when using it. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. A total of 14 pins are present on the instrumentation amplifier. Op amp ic rates 900μV for input offset voltage. For this electrical component, the recommended mounting type is Through Hole, which is the most common. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. As long as the supply current of the chip does not exceed 57μA, this op amp ic can operate. There should be no change in the voltage gain. There is an operating supply voltage rating of 4 for this operational amplifier, which is rated at the manufacturer. This buffer amplifier is assigned within the LinCMOS? series by its manufacturer.

TLC27L9IN Features


14 Pins
supply voltage of 10V
113.62dB voltage gain

TLC27L9IN Applications


There are a lot of Texas Instruments TLC27L9IN Instrumentational OP Amps applications.

  • Inverse/same-phase proportional circuit
  • Measurements of Wheatstone bridge
  • Biopotential
  • High/low-pass filter circuit
  • Logarithmic operation circuits
  • Semiconductor detectors
  • Band-stop filter
  • Medical imaging
  • Navigation
  • Television

Write a review

Note: HTML is not translated!
    Bad           Good