Parameters |
Package / Case |
8-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
8 |
Operating Temperature |
0°C~70°C |
Packaging |
Tube |
Series |
LinCMOS™ |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Terminal Position |
DUAL |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
TLC27 |
Pin Count |
8 |
Number of Elements |
2 |
Power Supplies |
5/10V |
Operating Supply Current |
285μA |
Nominal Supply Current |
600μA |
Power Dissipation |
1W |
Slew Rate |
0.62V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
65 dB |
Current - Input Bias |
0.7pA |
Voltage - Supply, Single/Dual (±) |
3V~16V ±1.5V~8V |
Output Current per Channel |
30mA |
Input Offset Voltage (Vos) |
5mV |
Bandwidth |
525 kHz |
Gain Bandwidth Product |
635kHz |
Unity Gain BW-Nom |
525 kHz |
Voltage Gain |
104.61dB |
Average Bias Current-Max (IIB) |
0.00006μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
900μV |
Low-Bias |
YES |
Micropower |
YES |
Bias Current-Max (IIB) @25C |
0.00006μA |
Programmable Power |
NO |
Nominal Gain Bandwidth Product |
525 kHz |
Max I/O Voltage |
5mV |
Input Offset Current-Max (IIO) |
0.00006μA |
Height |
5.08mm |
Length |
9.81mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mounting Type |
Through Hole |
TLC27M2ACP Overview
There is a 8-DIP (0.300, 7.62mm) case in which the instrumentation amplifier is packaged. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. There have been a total of 8 terminations over the past year. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. In total, the buffer amplifier consists of 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 5mV. This electronic part is recommended for mounting type Through Hole. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . Operational amplifier can operate supply current at 285μA. It is a member of the 104.61dB's 104.61dB family. As a whole, there are 2 elements that make up this buffer amplifier. LinCMOS? corresponds to linear amplifier's series.
TLC27M2ACP Features
8 Pins
supply voltage of 5V
104.61dB voltage gain
TLC27M2ACP Applications
There are a lot of Texas Instruments TLC27M2ACP Instrumentational OP Amps applications.
- Band-stop filter
- Fast A/D and D/A converters
- Power generator
- RF cable systems
- Vehicle electronics
- Micro signal measurement
- Test equipment
- Inverse/same-phase proportional circuit
- Signal amplification
- Navigation