TLC27M4BCDG4
| Parameters | |
|---|---|
| Base Part Number | TLC27 |
| Pin Count | 14 |
| Number of Elements | 4 |
| Power Supplies | 5/10V |
| Operating Supply Current | 570μA |
| Nominal Supply Current | 1.2mA |
| Power Dissipation | 950mW |
| Slew Rate | 0.62V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.7pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 525 kHz |
| Gain Bandwidth Product | 635kHz |
| Unity Gain BW-Nom | 525 kHz |
| Voltage Gain | 104.61dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 260μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 525 kHz |
| Max I/O Voltage | 2mV |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
TLC27M4BCDG4 Overview
In the package, you will find a 14-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. Buffer amps of this type are called General Purpose-types. A Tube case is used for delivering the op amp. It is estimated that there will be 14 terminations in the next few months. A total of 14 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 14 pins on it. Op amp rates 2mV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . A supply current of 570μA can be used to operate this linear amplifier. 104.61dB should remain the voltage gain. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 4. LinCMOS? corresponds to the op amp's series.
TLC27M4BCDG4 Features
14 Pins
supply voltage of 5V
104.61dB voltage gain
TLC27M4BCDG4 Applications
There are a lot of Texas Instruments TLC27M4BCDG4 Instrumentational OP Amps applications.
- Hand-held batteries
- Radiation thermometry transducers
- Laptop
- PDA
- Communication device
- Inverse/same-phase proportional circuit
- Large motor controllers
- Weighing systems
- Fast A/D and D/A converters
- Ultrasound transducers
