TLC27M4CD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLC27 |
| Pin Count | 14 |
| Power Supplies | 5/10V |
| Number of Channels | 4 |
| Operating Supply Current | 570μA |
| Nominal Supply Current | 1.2mA |
| Power Dissipation | 950mW |
| Slew Rate | 0.62V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.7pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 525 kHz |
| Gain Bandwidth Product | 635kHz |
| Unity Gain BW-Nom | 525 kHz |
| Voltage Gain | 104.61dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 525 kHz |
| Max I/O Voltage | 10mV |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC27M4CD Overview
Packaged in a 14-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tube case. It is estimated that there will be 14 terminations in the next few months. In this case, there are 14 pins on the board. I would like to remind you that this buffer op amp should be powered by an 5V battery. It should be noted that this op amp is a type of Operational Amplifier device. An 14-pin op amp ic is included in the package. There is an input offset voltage of 10mV for this buffer op amp. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureAn 570μA volt supply current is needed for this linear amplifier to operate. 104.61dB should be the voltage gain. On the buffer amps, there are 4 channels that can be used. The LinCMOS? indicates the series number of the op amp.
TLC27M4CD Features
14 Pins
supply voltage of 5V
104.61dB voltage gain
TLC27M4CD Applications
There are a lot of Texas Instruments TLC27M4CD Instrumentational OP Amps applications.
- MP3
- Precision measurement
- Band-pass filter
- Television broadcasting equipment
- Video data acquisition
- Broadcasting
- Digital cameras
- Automotive sensors
- Division circuits
- Communication device
