Parameters |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
TLC27 |
Pin Count |
8 |
Operating Supply Voltage |
8V |
Number of Elements |
2 |
Power Supplies |
5/10V |
Operating Supply Current |
285μA |
Nominal Supply Current |
600μA |
Power Dissipation |
1W |
Slew Rate |
0.62V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
65 dB |
Current - Input Bias |
0.7pA |
Voltage - Supply, Single/Dual (±) |
3V~16V ±1.5V~8V |
Output Current per Channel |
30mA |
Input Offset Voltage (Vos) |
500μV |
Bandwidth |
525 kHz |
Gain Bandwidth Product |
635kHz |
Unity Gain BW-Nom |
525 kHz |
Voltage Gain |
104.61dB |
Average Bias Current-Max (IIB) |
0.00006μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
190μV |
Low-Bias |
YES |
Micropower |
YES |
Bias Current-Max (IIB) @25C |
0.00006μA |
Programmable Power |
NO |
Nominal Gain Bandwidth Product |
525 kHz |
Max I/O Voltage |
500μV |
Input Offset Current-Max (IIO) |
0.00006μA |
Height |
5.08mm |
Length |
9.81mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 5 days ago) |
Mounting Type |
Through Hole |
Package / Case |
8-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
8 |
Operating Temperature |
0°C~70°C |
Packaging |
Tube |
Series |
LinCMOS™ |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
TLC27M7CP Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Tube case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. There are 8 pins on this chip. Op amp rates 500μV as input offset voltage. For this electrical component, Through Hole is the recommended mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . Using a supply current of 285μA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 104.61dB at all times. 2 elements make up the design of this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 8V. As the name implies, LinCMOS? refers to the series of the buffer op amp.
TLC27M7CP Features
8 Pins
supply voltage of 5V
104.61dB voltage gain
TLC27M7CP Applications
There are a lot of Texas Instruments TLC27M7CP Instrumentational OP Amps applications.
- Proportional counter tubes
- Strain gauges
- Video data acquisition
- Addition operation circuits
- Oscilloscopes
- Measurements of Wheatstone bridge
- Weighing systems
- Fission chambers
- Vehicle electronics
- Exponential operation circuits