TLC393IP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 440.409842mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | General Purpose |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Comparator |
| Max Power Dissipation | 1W |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC393 |
| Pin Count | 8 |
| Output Type | MOS, Open-Drain |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Power Supplies | 5V |
| Nominal Supply Current | 40μA |
| Power Dissipation | 1W |
| Output Current | 20mA |
| Max Supply Current | 20μA |
| Propagation Delay | 4.5 μs |
| Quiescent Current | 65μA |
| Response Time | 2500 ns |
| Common Mode Rejection Ratio | 84 dB |
| Voltage - Supply, Single/Dual (±) | 3V~16V |
| Output Current per Channel | 6mA |
| Input Offset Voltage (Vos) | 5mV |
| Power Supply Rejection Ratio (PSRR) | 85dB |
| Input Bias Current | 5pA |
| Current - Quiescent (Max) | 65μA |
| Voltage - Input Offset (Max) | 5mV @ 10V |
| Current - Input Bias (Max) | 5pA @ 5V |
| CMRR, PSRR (Typ) | 84dB CMRR |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC393IP Overview
In order to facilitate transportation, it is packaged in 8-DIP (0.300, 7.62mm) .There is a MOS, Open-Drain output type for this comparator.Electronic comparator is shipped by Tube .The comparator has 8 terminals.The chip belongs to Comparator .When supplied with 5V voltage, the comparator is capable of performing a wide range of tasks.In terms of type, this is a typical General Purpose comparator.Currently, it consists of only 2 elements.Electronic comparator has 8 pins.The recommended mounting type is Through Hole .Electronic comparator is recommended that you set the operating temperature to -40°C~85°C in order to prevent malfunctions.There are 8 pins on the comparator.If you require more pin-to-pin solutions, search TLC393 for more options.There is a quiescent current of 65μA in this comparator.The PCB or other board can be mounted using the Through Hole on it.Electronic comparator is recommended that the nominal supply current for the device be set to 40μA .Current supply exceeding 20μA could cause disfunction of the compartator.5V power supplies are enough to run the device.In this case, the part is from the LinCMOS? comparator series.In order to operate normally, a supply voltage of 0 is required.
TLC393IP Features
MOS, Open-Drain output capability
General Purpose IC
Employing 2 elements
Operates under -40°C~85°C
Quiescent Current: 65μA
TLC393IP Applications
There are a lot of Texas Instruments TLC393IP linear comparators applications.
- Point of load regulators
- Portable and Battery-Powered Systems
- Limit Comparators
- Laptop Computers
- Wireless Base Stations
- Power management
- Mobile Communications
- Consumer Medical Electronics
- Set Top Boxes
- Simple Analog-to-Digital Converters (ADCs)
