TLC4501ACD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | LinEPIC™, Self-Cal™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLC4501 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1.5mA |
| Power Dissipation | 725mW |
| Output Current | 50mA |
| Slew Rate | 2.5V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4V~6V ±2V~3V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 40μV |
| Bandwidth | 4.7MHz |
| Unity Gain BW-Nom | 4700 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 10μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Max I/O Voltage | 40μV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLC4501ACD Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. Op amps are General Purpose types of amplifier on the chip. A Tube case is used for delivering the op amp. In recent months, the number of terminations has approached 8. In this case, there are 8 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. Linear amplifier includes 8 pins. Regarding input offset voltage, buffer amplifier rates 40μV voltage. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around 0°C~70°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 1mA and 10 . 120dB should remain the voltage gain. Op amp ic has 1 channels. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The LinEPIC?, Self-Cal? represents the op amp's series number.
TLC4501ACD Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
TLC4501ACD Applications
There are a lot of Texas Instruments TLC4501ACD Instrumentational OP Amps applications.
- Displayers for aircraft and air transportation control systems
- Non-polarized electrodes
- Industrial control system
- High/low-pass filter circuit
- Tablets
- High speed sample
- Proportional operation circuits
- ECG equipment
- Proportional counter tubes
- Instrumentation
