TLE2081ACD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | Excalibur™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIFET |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLE2081 |
| Pin Count | 8 |
| Operating Supply Voltage | 19V |
| Number of Elements | 1 |
| Operating Supply Current | 1.7mA |
| Nominal Supply Current | 2.2mA |
| Power Dissipation | 725mW |
| Output Current | 48mA |
| Slew Rate | 45V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~38V ±2.25V~19V |
| Output Current per Channel | 48mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 9.4MHz |
| Gain Bandwidth Product | 10MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 9400 kHz |
| Voltage Gain | 106dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 470μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 9.4MHz |
| Max I/O Voltage | 3mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLE2081ACD Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp ic of the J-FET type. In the case of Tube cases, linear amplifier will be delivered. It is estimated that there will be 8 terminations in the next few months. The pins on this board total to 8 in total. Please take in mind that this instrumentation amplifier should be run at 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are included on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 3mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . An 1.7mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 106dB for the time being. There is a rating of 1 for the operating supply voltage of the buffer op amp. The operating supply voltage of instrumentation amplifier is rated 19V voltage. The Excalibur? represents the op amp's series number.
TLE2081ACD Features
8 Pins
supply voltage of 5V
106dB voltage gain
TLE2081ACD Applications
There are a lot of Texas Instruments TLE2081ACD Instrumentational OP Amps applications.
- Oscilloscopes
- Wireless base stations
- Automotive sensors
- Navigation
- earphone
- Semiconductor detectors
- Measurements of Wheatstone bridge
- Signal amplification
- High input resistance broadband
- Vehicle electronics
